A Slide Show

A small table from scrap pieces

I had intended to post part II of the Three Rivers series before posting about anything else, but it has been some time since I’ve posted about furniture and I’ve just finished this new piece so I thought I’d sneak this post in now.

We needed a table of just the right height to hold a fan in our bedroom window at home.  Although I am in the midst of a pretty big project just now I thought I’d check out a few of my scrap piles to see if there was anything there to inspire me.

And, while I was at it, maybe I’d check out the paint locker and see what was lurking in there.

Here’s what caught my eye:

A couple of pieces of MDF, some interesting walnut cut-offs and a nice green latex paint.

I glued up the MDF pieces into a block 1-1/2″ thick-

Cut the walnut cut-offs to a uniform length-

Then drew a pleasing curve to shape the legs.

I cut out the first leg, used it as a pattern to trace out the other two, cut them on the bandsaw and sanded the curved cut.

Next I created a guide for my router to cut out the mortises into the top that would hold the legs.

The legs were rounded over on the router table on the long straight face.

I used a variety of implements to draw out a pattern for the top, created a template for 1/2 of the top, transferred that shape onto the top, flipping over the template to get the other half so that the curves would be symmetrical and shaped the top.

I wanted to create an interesting joint detail where the legs met the top. I did some sketching and decided that the top should have its bottom edge rounded. This was done on the big shaper, a finger chewing machine if there ever was one.

I managed to get the top rounded with out loosing any fingers and proceeded to cut the mortises on the under side of the top using the jig I had created earlier.

I adjusted the fit of the legs into the mortises by carefully sanding down their final thickness.

You can start to see what this table will look like at this stage. I still need to square off the round corners left by the router bit in the mortises. I did this by hand using a sharp chisel.

Now I was able to see if the joint detail came out like I had hoped.

OK, this was what I wanted. A look as if the legs were cradling the top. This is reminiscent to me of the original tripod that held a bowl or tray from eons ago.

And here’s the table before finishing:

I painted the top, glued in the legs, rubbed on some of my special oil/ varnish mix and the table was complete.

:: :: :: :: :: :: :: :: :: :: ::

The next table. part 3

With the veneers glued on I do some final trimming of the top.

I use sharp chisels with masking tape applied the areas that will ride along the face adjacent to the veneer being trimmed so that I only cut what needs to be trimmed. A sharp knife and guide board also comes in handy.

I then use a card scraper to flatten the veneers.

Once everything is as flat as possible without scraping through the veneer to the paper backing beneath I apply a black dye and start building up the layers of polyurethane finish.

This process will take some time and will require a few adjustments as it progresses. I’ve started with gloss polyurethane varnish to build up the base coats but will finish with a semi-gloss finish. It is important to keep the shop, or at least this area of it, as dust free as possible while the varnish dries.

Part 4 is here. Part 2 is here.

:: :: :: :: :: :: :: :: :: :: ::

Glass base

Some time ago a delightful young lady called my studio. She had an idea for a table she wanted but had become very frustrated in trying to find aomeone that would make the table for her. I invited her in to the studio and she layed out her idea for me. It was very challenging. She wanted the table to be completely supported by two glass panels.

I thought it over and developed a rough idea about how it could be accomplished. My price came in considerably higher than her budget for this project however. I offered to lower my price  if she would handle the purchasing of the glass. We also agreed that the project would be put on hold until she was able to save enough money for it. I believe it was a year later that she called back and was ready to proceed.

Along with the chairs she found here is the result.

:: :: :: :: :: :: :: :: :: :: ::

The next table. part 1

I’m finishing a project that was originally commissioned exactly one year ago. It got delayed because the end user wanted to have a chair re-upholstered and wanted to be sure that this table came out to the exact same height as the arm of the chair. The upholsterer took quite a while to get that job done so even though I had been given the deposit, had completed the drawings, had started making the tooling required and had purchased some of the materials I was told to hold off until the chair was done.

This table is a pedestal with curved sides veneered in maple, dyed black and finished with a polyurethane semi-gloss finish.  Here’s a screen grab from the design I created.

This design was based on a table my client, an interior designer, found elsewhere and asked me to modify to suit the end user.

I decided to carve the shape out of stacked MDF board. I had done this before, for the same client and end user actually, on a piece that was finished by Catherine Lottes.

I started by making two stacks.

Then glued the 2 halves together.

To create the shape from the glued up stack, the work piece, I designed a “machine” to guide a grinder with a cutter attached. I used my Rhino program to design the machine.

The work piece is shaped on one face then the machine is taken apart and the work piece is rotated 90 degrees about the vertical axis (vertical when the table is standing upright) and the machine is put back together around the work piece to carve the next face. The grinder that spins the cutter is fixed to a piece of PVC pipe that rides on guides attached to the carriage. The carriage in turn rides on rails from side to side. I can easily lift the cutter assembly out as well as slide the carriage out to access the work piece for final sanding.

Here’s the machine in action.

Some interesting textures are created in this process and I would like to make a table using this process that would retain the texture in some way.

See part 2 for the next phase of the making of this table.
:: :: :: :: :: :: :: :: :: :: ::

part 2

Oh what a long time it’s been…

…since I’ve last posted.

I have been working on such a number of interesting projects. There’s one, really interesting one that has been mostly in the planning stages.  I’ll have to wait just a little longer before I can post about it. But, I’ve been busy in shop as well.

I’ve been working on a couple of tables for a long time client. Both of these are headed for my client’s Florida home. The first one is a very large coffee table. It measures 88″ by 55″. But the wild thing about it is that it is not flat. The top is wavy.

Todd cutting the table to size.

Here I am cutting of the end of the glued up butternut planks. The table was too big to run through my table saw and a sharp handsaw works just as well.

The planks had a natural curve to them so during glue up I took as much advantage of this as possible.

Carving the surface with disc grinder.

Here you can see some of the waviness. The table was so large and heavy that I had to plan my work to minimize how often I turned the piece over. I carved out the bottom face first then flipped it using a block and tackle.

I used a number of tools to shape the top.  Here are a few, ready at hand.

The final sanding was very tedious, but since this table was to be varnished with a gloss spar varnish it was very important. I spent a lot of time carefully sanding the top.

Careful sanding was a must.

The table is wrapped in blankets now and I haven’t taken any pictures of the final finish. I’ll try and get to that before the trucking company shows up.

Update: I found s few more images.

One of the base units being fit to the table top.

This and the next picture is of the table upside down as the two boxes that act as the base for the table are being fit to the wavy underside of the table top.

The 2 base boxes being fit.

The next project was another table with curves, for the same clients. That’ll be in the next post.

Update 2: I pulled back the blankets and took a picture of the finished table top.

Surf Board Table III -vi

I mix a custom blend for my wipe on, oil finish. After the oil mix is applied I allow it to soak into the wood then wipe it dry. I’ll apply at least three coats, buffing with very fine steel wool in between coats. Each coat takes a day to dry.

After the second coat of dye dries on the base I’ll apply the oil mix over the dye.

 

Next

Surf Board Table III -v

I’ve attached the cross pieces onto the base structure and after a little final sanding it is ready to be dyed black.

I use a water based aniline dye. It will take two applications with some light sanding in between to give a nice even color. The water based dye will not fade when exposed to uv light as will alcohol based dye. Water based dye does raise the grain a little, hence the extra sanding step.

While the base dries I work on sanding the edges of the top.

It’s important to not overlook any detail at this stage. Soon I’ll be applying the finish and any touch-ups or adjustments will be very hard to do after that.

The edges are staring to look nice and wood grain is starting to show it’s beauty. The top needs a final sanding and I will be ready to apply the finish.

As I work through ever finer grades of sandpaper, to bring out the true beauty of the wood, various small scratches begin to appear. They were always there, but were so fine that they weren’t visible until the wood around them is sanded with a very fine grit. The scraper takes very fine shavings off these areas, which will then be further sanded so that the top has a uniform, very fine, surface.

Next

Surf Board Table III -iii

The legs are cut to fit up against the center arc at a 30 degree angle and mortises or slots are cut on that beveled face to receive the tenons that fit through the arc. I use the arc pattern to locate the slots in the arc.

After cutting those I do the final shaping on the arc. The convex curve is shaped on the belt sander table.

And the concave curve is shaped by hand using a spoke shave.

A test assembly of two of the legs to the arc reveals an interesting form.

I often take a little time to consider the forms created by accident when assembling furniture elements. To some degree there is not that much “accident” involved as I intentionally created the parts with the goal of creating an interesting or compelling shape.

I use to whip out an old Polaroid camera and take a few shots. Then I’d pin them to my office wall. I still study them for ideas.

Now I use one of digital cameras and my hard drive has become the studio wall. I actually like the studio wall better.

Adding the second set of legs makes it easier to see how this could turn into a coffee table.

Next I’ll shape the top, add some cross pieces and I can glue up the base.

Next post is here.

Surf Board Table III -ii

Part 2 in the making of the surf board coffee table.

One more check of the pattern with the boards test clamped then I trace the pattern onto the boards to help me align them during glue up.

I gather up my supplies- wood glue, shop made applicator, extra clamps, wax paper and a rag -and bring them to the glue up frame area of the shop. You can see the boards set on the glue up frame in preparation of a test clamp. Once you start spreading the glue you have to work fast to get the boards set up on the frame, aligned and clamped so it pays to have everything you may need at hand.

Here’s the glue up frame with the work pieces all clamped in the test clamp. This is the time to decide if you need more clamps, cross palls or other supplies.

The cross palls are, in this case 2 x 4s, clamped across the direction of the glue joints to hold the boards in alignment and in a single plane. They also keep the whole glue-up assembly from popping off the frame when I crank down on the bar clamps.

Now I take everything down and spread the wood glue on the edges to be glued.

Did I mention that you have to work fast to do this?

While the top is in the clamps as the glue sets I work on cutting out the legs.

Once the legs are cut out on the band saw they go to the drum sander to sand out the saw blade marks and get the legs to their final shape.

to be continued…. here

Surf Board Table III

Hmm, maybe it should be “surfboard table” instead of “surf board table”. I better check it out.

I got another order for one and have taken a few shots of the some of the steps in making one. This is a very general description of the process and is not intended as instructional.

The first step was to check my lumber supply to see if I had some nice pieces on hand that would work for this table. I generally make these out of maple and ash, with a nice strip of walnut as the stringer, the center strip of wood on the top. I didn’t have enough maple and needed a little more ash so I drove down to my favorite lumber yard last Friday and sorted through their stacks. I found some nice maple and just enough ash.

I like to let the wood sit in my shop for a few days before I start working with it, especially in the winter when the heat is on and my shop may be warmer and drier than the lumber yard. Wood is a fickle material and to work it you need to understand and respect it. Moisture moves in and out of wood through hollow cells that are arrayed in unique ways for each piece of wood. As the moisture enters the wood the cell expands, as it leaves the cell shrinks. When you get thousands of these cells expanding and contracting the piece of wood changes shape. My job is to work with the wood to shape it into the shapes that I want. Sometimes that means just letting the piece sit for awhile and acclimate to a new environment.

I planed flat and glued up the ash for the long arc under the top and laid a pattern for the arc over the wood, traced the outline and cut it out on the band saw.

I then selected the wood for the top. I start by eyeing the boards to check for warp and twist and carefully noting the grain pattern. I use the half pattern for the top to determine the best way to cut the boards to length.

Here is the half pattern on the boards that I’ve cut to roughly the length I need.

A half pattern is a great way to make sure that a shape is symmetrical. You just trace the shape out on one side and flip the pattern over, line it up and trace the other side.

The next step is to flatten the boards to eliminate as much twist and cupping as you can before glue up. The narrower pieces can be run over a jointer, face down. This tool has cutters on a drum that rotate so that the top edge of the cutters is exactly even with the outfeed table. Several passes and you have a flat face, for now.

The wider pieces have to be run through my planer with a carriage. A planer has the cutters above the board and will trace the same twist and warp that a board already has as the board passes through it. By shimming the work piece so that it doesn’t rock, onto a flat carriage that can then pass through the planer you can cut off the high points and after many passes arrive at a relatively flat board.

Eventually I can get the boards relatively flat at least on one face.

I then pass each of these boards through the planer again, but with out the carriage. I place the flat face down and the planer will trace this flat surface onto the opposite face, hopefully ending with a very flat board.

I qualify the above because I also have to take into account the way a piece of wood reacts when you remove part of it. Some of those cells that take on and give off moisture were held in tension by others. By removing some of the cells the others can relax into a different shape. As this happens I try different strategies while running the boards through the planer to compensate. I may flip and reverse a board, I may press on it as it comes out, it is surprising how physical an activity this really is.

After the boards are flat on their faces I lay them out again as they will be glued up and lay the pattern on them once more. I now determine how wide each board has to be to be able to create the pattern of grain movement and color that I want for the table top. This also allows me to see which edges I need to straighten by running the edge over the jointer.

After I get one of the edges straight and square with the two faces I then saw the board to its final width by passing it through the table saw.

This process of truing the edges is time consuming as it is critical to getting good glue joints.

I recheck with the pattern to make sure the pieces are lining up with true edges the way I want and I’m ready to glue the pieces together into one large blank ready to be cut out, sanded and finished.

I’ll blog more on this process soon.

 

 

Part 2 here

 

Surf Board Table II

There seems to be some interest in the surf board table I posted about a little while ago so I thought I’d post this image of the completed table. If you are interested in having me make one for you I would be very happy to just get in touch.

-Todd